Special Offer

XBee S2 MODULE

New

9 Items

₹ 999.00

This is the new 2.4GHz XBee S1 module from Digi.  These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.

More details

Add to my wishlist

Special Offers!
  • Lorem ipsum dolor sit amet, consectetuer adipiscing elit.
  • Fusce lobortis lorem at ipsum semper sagittis...
  • Integer vitae libero ac risus egestas placerat...
  • Donec quis dui at dolor tempor interdum...
  • Praesent placerat 100% free risus quis eros....
Order on Phone 1800 000 12345call
STATIC BLOCK

This is the XBee 2mW Wire Antenna - Series 2 XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.

Specifications:

  • Model code: XB24-Z7WIT-004
  • Operating Frequency: ISM 2.4 GHz
  • Antenna type: Wire antenna
  • Indoor/Urban Range up to 133 ft. (40 m)
  • Outdoor RF line-of-sight Range up to 400 ft. (120 m)
  • Interface: Serial(UART) at 1200 - 1 Mbps
  • Supply Voltage: 2.1 – 3.6 V
  • Transmit Current 40mA (@ 3.3 V boost mode enabled)
  • Receive Current 40mA (@ 3.3 V boost mode enabled)
  • Dimensions: 0.960” x 1.087” (2.438cm x 2.761cm)
  • Operating Temperature: -40 to 85º C (industrial)

Features:

  • Supported Network Topologies: Point-to-point, Point-to-multipoint & Peer-to-peer
  • Number of Channels: (software selectable) 16 Direct Sequence Channels
  • Addressing Options: PAN ID, Addresses,Cluster IDs and Endpoints
  • 128 bit encryption
  • 8 Digital IO pins
  • AT and API Command Modes for configuring module parameters
  • Fully FCC certified
  • Transmit Power: 2 mw(3 dBm)
  • Receiver Sensitivity: -96 dBm

Please Note: If you are looking for a simple point-to-point configuration, you might want to try the Series 1 instead. The Series 2 requires considerable setup and configuration. Also Series 1 and Series 2 XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules.

No customer comments for the moment.

Write a review

XBee S2 MODULE

XBee S2 MODULE

This is the new 2.4GHz XBee S1 module from Digi.  These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.

Write a review

Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Donec odio. Quisque volutpat mattis eros. Nullam malesuada erat ut turpis. Suspendisse urna nibh, viverra non, semper suscipit, posuere a, pede. Sed adipiscing ornare risus. Morbi est est, blandit sit amet, sagittis vel, euismod vel, velit. Pellentesque egestas sem. Suspendisse commodo ullamcorper magna.
 

Secure Shopping

 
 

24/7 Customer Service

 
 

100% Guaranteed

 
 

Free & fast shipping